220V DDS5188 LCD Digital Din Rail Electric Meter 5-25A For Kilowatt Hour Kwh Meter

1、The meter is fully in conformity with the relevant technical requirements of GB/T17215.321-2008 national standard and the IEC62053 international standard of grade 1 or level 2 single-phase energy meter, which can directly and accurately measure active en

2、LCD display is 7+1 or6+1meter shows the total power consumption

3、It features high reliability, small volume, light weight, beautiful appearance, advanced technology, and 35mmDIN standard guide rail installation, etc

4、It has good anti-electromagnetic interference, low power consumption, high precision, high overload, high stability, anti electricity-stolen and long life

5、This table is suitable for the measurement of rated frequency 50 Hz or 60 Hz single-phase ac active electricity, used for fixed installation indoors, apply to the environment temperature is -25 ℃ ~ 55 ℃, relative humidity is ≤ 95%, and in the air does no

Descriptions:

The meter is fully in conformity with the

relevant technical

requirements of GB/T17215.321-2008 national standard and the IEC62053

international standard of grade 1 or level 2 single-phase energy meter,

which can directly and accurately measure active energy of the energy

consumption. It features high reliability, small volume, light weight, beautiful

appearance, advanced technology, and 35mmDIN standard

guide rail installation, etc.

Features:

The

meter is fully in conformity with the relevant technical

requirements of GB/T17215.321-2008 national standard and the IEC62053

international standard of grade 1 or level 2 single-phase energy meter,

which can directly and accurately measure active energy of the energy

consumption.

LCD display is 7+1 or 6+1meter shows the total power consumption.

It features high reliability, small volume, light weight, beautiful

appearance, advanced technology, and 35mmDIN standard

guide rail installation, etc.

It has good anti-electromagnetic interference, low power consumption,

high precision, high overload, high stability, anti electricity-stolen and long

life.

This table is suitable for the measurement of rated frequency 50 Hz or

60 Hz single-phase ac active electricity, used for fixed installation

indoors, apply to the environment temperature is -25 ℃ ~ 55

℃, relative humidity is ≤ 95%, and in the air does not

contain corrosive gases and avoid dust, mold, salt fog, condensation,

insects, etc.

Specifications:

Model: DDS5188

Phase number: single phase

Type: guide type

Display mode: LCD

Rated voltage: 220V

Rated current: 5-25A

Working temperature: -25 ℃ ~ 55 ℃

Rated frequency: 50-60Hz +/- 10%

Accuracy level: level 1 (equivalent to measurement error < 1%)

Including S0 port 2000Imp/kWh (ti = 80ms)

Relative humidity: 95%

Size: as the picture

Weight: 97g

Wiring:

Test:

The meter has photoelectric coupling type electric pulse test output

port, located in terminal button box (as shown in figure 2), + 5 VDC

of the test equipment connected to 20" + "terminal, signal S connected

to 21"-" terminal.

Installation considerations:

1. Installation of electric meter required experienced electrician or professionals.

2.Electric meter should be installed in indoor ventilated and dry place, adopt 35mm DIN standard guide type installation,the bottom plate of the electric energy meter shall be fixed to the rigid refractory, non-vibrating wall.

3.The bottom plate of the electric energy meter shall be fixed to the rigid refractory, non-vibrating wall.

4. Electricity meters should be installed in protective cabinets in places where there are filth and potential damages.

5.

The installation should be in accordance with the wiring diagram,

preferably with a multi-strand copper wire, avoiding the abnormal or

burning of the electricity meter because of the bad contact.

6. When the electricity meter is correctly connected to the power grid, the power indicator of the meter is on

7.

Electric meter should take the lightning protection measures

when it is used in the area with more lightning, so as to avoid damaging

the electric energy meter by lightning.

The load capacity of the electricity meter is 0.05Ib~Imax (direct access)

Power indication: when the green light on, indicates that working power supply is normal

Pulse indication: when the red light on, indicates that the power pulse is detected

When there is a sampling signal, the pulse light is about 80ms

Package Included:

1 x DDS5188 Din-rail Kwh Meter