225 m × 1 m self-adhesive protective fleece, 140 g/m² – Painter’s and stair fleece for renovation, wallpapering and refurbishment

AQUAGART Self-Adhesive Cover Fleece 140 g/m² – 1 × 25 m

Absorbent painter’s fleece and stair protection fleece made from 100% polyester, with a self-adhesive, waterproof LDPE film – 25 m² of coverage for renovation, painting, wallpapering and moving work.

Self-Adhesive Floor Protection for Renovation Work

AQUAGART self-adhesive cover fleece protects suitable floors, stairs and walkways during painting, wallpapering, renovation, refurbishment or moving work. The self-adhesive film side provides good hold on suitable smooth surfaces and helps reduce slipping or shifting of the protective fleece.

The roll is 1 m wide and 25 m long, providing a total coverage area of 25 m². The white fleece is made from 100% polyester, has a basis weight of approx. 140 g/m² and is approx. 1 mm thick.

Absorbent Fleece Surface with Moisture Protection

The absorbent PES fleece surface absorbs moisture, paint, paint splashes and typical work-related dirt. The transparent self-adhesive LDPE film on the underside is waterproof and, when the material is intact, prevents moisture or paint from penetrating through to the floor below.

Benefits of AQUAGART Cover Fleece

• 25 m² coverage: Each roll is 1 m wide and 25 m long.
• Absorbent surface: The PES fleece absorbs moisture and paint.
• Waterproof underside: The LDPE film protects the substrate against penetrating moisture.
• Self-adhesive film side: Helps reduce slipping or shifting on suitable surfaces.
• Easy to adapt: The cover fleece is easy to unroll and cut to size as needed.
• Versatile use: Suitable for painting, wallpapering, renovation, refurbishment and moving work.
• For floors and stairs: Can be used as floor protection, stair fleece and as a covering for walkways.
• Conditionally reusable: Can be reused if clean, undamaged and still sufficiently adhesive.

Areas of Application

• Painting and varnishing work
• Wallpapering work
• Renovation and refurbishment
• Conversion and construction work
• Moving house and furniture transport
• Covering suitable floors and stairs
• Protection of walkways and work areas

Installation Instructions

1. Allow the substrate to dry completely and clean it thoroughly.
2. Completely remove dust, dirt and release agents.
3. Lay the fleece with the self-adhesive film side facing down.
4. Unroll the cover fleece as smoothly and wrinkle-free as possible.
5. When laying several strips, allow an overlap of approx. 10 cm.
6. If necessary, additionally secure the edges with suitable adhesive tape.
7. Remove wrinkles and potential trip hazards immediately.

Important Notes on the Substrate

The substrate must be completely dry, clean, dust-free, free from release agents and sufficiently resistant to tensile and compressive stress. The cover fleece is not suitable for newly laid floor coverings, porous stone surfaces or clay tiles. A vapour-permeable covering alternative should be used for such substrates.

For waxed or varnished wooden and parquet floors, as well as older or heavily used surfaces, carry out a test in an inconspicuous area before applying the product over a large area. Due to differing materials and environmental conditions, completely residue-free removal cannot be guaranteed for every substrate.

Reuse and Removal

The cover fleece can be reused if it is clean, undamaged and still sufficiently self-adhesive. Before each reuse, check both the fleece and film sides for dirt, residue, holes, tears, reduced adhesive strength or separation of the film.

When removing the fleece, do not pull it off vertically at a 90° angle from the substrate. The ambient temperature should be between +15 °C and +45 °C. Do not remove the cover fleece in frosty conditions.

Technical Data

Product type	Self-adhesive cover fleece
Fleece material	100% polyester (PES)
Basis weight	Approx. 140 g/m² (± 10%)
Film material	Polyethylene (LDPE)
Film thickness	Approx. 30 µm (± 10%)
Total thickness	Approx. 1 mm
Fleece colour	White
Film colour	Transparent
Roll width	1 m
Roll length	25 m
Coverage area	25 m²
Fleece/film property	Waterproof

Storage and Disposal

Under normal indoor conditions, the roll can be stored for approximately six months at temperatures between +10 °C and +30 °C. During storage, protect it from direct sunlight, excessive heat, dust and moisture.

After use, the cover fleece can be disposed of with normal household or residual waste.