300W Hot Air Gun – Heat Shrink Tool with Stand for Embossing and Paint Drying – 220V, White

Product Parameters

Product Name: DIY Soft Clay Hot Air Gun

Plug Type: European Plug

Product Voltage: 220V

Product Power: 300W

Temperature Range:> 200°C

Outlet Diameter: 12 mm

Product Packaging: Color Box

Product Weight: 213g (net weight), 275g (with packaging)

Product Application: Soft ceramics, DIY rubber stamp convex powder, embossing powder, heat shrink film

Power Source Type: AC Power

Notes

1. Do not use a heat gun to blow directly onto the object at a 90° angle.

2. The recommended distance between the air outlet of the heat gun and the object being heated is 5-6 cm.

3. The single use time of the heat gun should not be too long, generally 2 to 3 minutes.

This is because

The body temperature will obviously have risen, so please turn off the heat gun and wait for it to cool down before using it again.

4. The temperature of the heat gun can only reach approximately 200°C, and it is impossible to desolder small pieces of iron.

Industrial applications such as components and integrated circuits with chips

Instructions for power tools

When using power tools, in order to reduce accidents such as fires, electric shocks, and injuries, you must pay attention to the basic safety elements listed below; please read the following safety elements carefully before proceeding.

1. Keep the work area clean and do not use power tools in messy work areas and on cluttered work surfaces.

2. Do not use power tools in dark and damp places. Keep it out of the rain. Do not use in flammable liquids or where flammable gases are present.

3. Keep children and idlers away from the work area. Do not allow rollers to come near touch tools or power cords.

4. When the power tool is not in use, it should be stored in a dry place out of the reach of children and should be locked.

5. Maintain proper feed rate and pressure speed to make the tool operate more safely and sustainably.

6. Operate within the specified application range and do not exceed the limits for overload protection.

7. You must maintain a correct posture while working, you must remain steady, and you must not stretch your hands over the tools to pick things up.

8. The knives must be lubricated and replaced from time to time to keep them sharp, and the threads must be checked regularly.

9. When the tools are not in use or for maintenance, when changing attachments and knives, be sure to unplug the power cord.

10. Before turning on the switch to start the machine, check that the workpiece adjustment tools and the clamping wrench are completely removed.

11. To prevent accidental starting, you must check that the tool switch is off before inserting the plug into the power source. After switching on the power, do not frequently press the switch.

12. Outdoor Extension Cords: When using tools outdoors, be sure to use outdoor extension cords.

13. Do not wear loose clothing or accessories to avoid entanglement when the tool is running. Rubber gloves and non-slip industrial safety shoes must be worn outdoors. Protective hood.

14. Wear safety glasses and a dust mask when there is excessive chipping and dust.

15. Do not step on the wire, do not drag the wire-moving tool, and avoid touching the hot object and sharp metal edge or getting grease wet.

16. Secure the workpiece. Use clamps to secure the workpiece, which is safer than holding the workpiece by hand.

17. When repairing or replacing parts, be sure to use parts specified by the original manufacturer and send them to a professional repair center for replacement.

18. Pay attention to the workpiece and the tool being used. Tools should not be used when fatigued.

19. Before using the tool, you must carefully check if the tool guard or other parts are damaged and determine if the degree of damage will affect the normal operation of the tool. Check if all moving parts are in the correct position, if the parts to be fastened are fixed, etc. If the guard or other parts are damaged, or if there is a problem with the tool switch, please have it repaired or replaced by a specialist shop. Do not force a faulty switch to activate the tool.

20. During operation, your body must not come into contact with grounded metal objects, such as iron pipes, radiators, refrigerators, etc. Please allow for slight deviations in the measurements and ensure this is acceptable to you before ordering.