Automatic drip irrigation kit, intelligent waterless detection, watering tray for indoor and house plants, 5V

Features:1.POWER FAILURE MEMORY FUNCTION: Automatic plant waterer with power-off memory function. Once the program is set, the watering process will restart the next time.
2.AUTO HIBERATION: The automatic watering system is easy to use.After 1 minute of inactivity, the main unit goes into standby mode.
3.WATER-FREE DETECTION: The automatic drip irrigation kit has a water-free detection function. When the main unit detects a water shortage, the pump stops after approximately 10 seconds.
4.WIDE APPLICATION: The automatic watering system is suitable for home vegetable gardens, indoor gardens, or potted plants. Free your hands and save time.
5.Battery powered: The automatic indoor plant waterer uses 4 AA 1.5V alkaline batteries (not included) to operate this drip irrigation system.
Specifications:Item Type: Automatic Plant Waterer
Material: ABS
Pump Body Vibration Damping Material: Silicone
Weight: Approx.750g / 26.5 oz
Rated Voltage: 5V
Size: Approx.144x102x50mm / 5.67x4.02x1.97 inch
Hotline Length: Approx. 15m / 49.2ft
Power: 3.6W x 2
Interface Caliber: 4.8mm / 0.19 inch diameter
Compatible Pipeline: 4/6, 4/7
MAXIMUM WATER PRESSURE: ≥30 psi (200kpa)
Battery Type: 4 x AA 1.5V Alkaline Batteries (Shiphep without batteries)
Flow Rate: 0.3-0.8 Lpm
Working Temperature: 4℃-50℃
Lift: ≥2.5m / 8.2ft
Suction Range: ≥2m / 6.6ft

How to Use:1. Press and hold the power button for 3 seconds to turn it on or off. 2. Press and hold the MA button for 3 seconds to manually activate pump A. Press and hold it for 3 seconds to turn it off. 3. Press and hold the MB button for 3 seconds to manually turn on pump B. Press and hold it again for 3 seconds to turn it off. Automatic Program Setting. When the power is on, click the "Set" button to enter the program settings. Adjust the value by clicking the "+/-" button, then click the "Set" button to set the watering duration for a circuit (xx minutes xx seconds), a circuit interval (xx days xx hours), the circuit duration (xx minutes xx seconds), and the circuit interval (xx days xx hours). The watering duration range is: 1 second to 59 minutes and 59 seconds; The interval duration range is: 1 hour to 30 days and 23 hours. Press and hold the Plus or Minus button to quickly increase or decrease the value. If the value does not need to be changed, it can be dismissed by clicking the "Set" button. Once the setup is complete, the program will begin running.
Package List:1 x Automatic Plant Waterer (battery not included)
1 x Hose
1 x Connection Cable
1 x Storage Bag
1 x Manual
46 x Accessories
Note: 1. Position the water container slightly lower than the planter to prevent water from the bucket from flowing directly into the planter due to the siphon.2. Use the inlet pipe filter correctly and do not use large particles of wastewater as a water source to avoid clogging the pipes or pump.3.Before setting up the automatic program, you can use the manual function to test the watering duration and flow rate required.4.Please use indoors.5.When not in use for an extended period, unplug the adapter, remove the batteries, and store the main unit in a suitable dry environment.6.When using battery power alone, battery life depends on overall conditions such as operating frequency, operating resistance, and battery performance.When the low battery indicator starts flashing, the battery should be replaced promptly.When replacing the batteries, all four batteries should be replaced simultaneously.7.The automatic watering device can only water intermittently and cannot be used as a pump to continuously transport liquid media for extended periods, as this will severely reduce the lifespan of the main diaphragm pump.8.Please do not pump acid, alkali, or other corrosive liquids to avoid damaging the pump body.9.Please allow for slight errors in manual measurements.