DC-DC 10-60V to 12-97V 1500W 30A Boost Voltage Converter DC CV Power Supply Module

1. This is a non-isolated DC converter module with a long lifespan.
2. High power and stable output; it converts 10-60VDC to 12-97VDC.
3. High-quality components ensure high conversion efficiency, up to 97%.
4. Designed with an intelligent temperature-controlled fan, which will automatically activate when the temperature reaches approximately 60°C and stop when the temperature drops below 60°C.
5. Widely used for driving high-power solar streetlights, various LED lighting circuits, powering mobile and vehicle-mounted devices, DIY adjustable DC-DC power supplies, solar power charging, and charging various batteries.

Specification:

Features:
This is a non-isolated DC power converter module with a long service life.
High power and stable output; it converts 10-60VDC to 12-97VDC.
High-quality components ensure high conversion efficiency, up to 97%.
Designed with an intelligent temperature control fan, which will automatically activate when the temperature reaches approximately 60°C. and will stop when the temperature drops below 60°C.
Widely used for driving high-power solar streetlights, driving various CV LED lights, powering mobile and vehicle-mounted devices, DIY adjustable DC power supplies, solar power charging, and charging various batteries.
Specification:
Name: 1500W Constant Current Boost Module
Type: Non-isolated Boost Module
Input Voltage: DC10V to 60V
Input Current: Input voltage 10V-30V, maximum current is 35A-40A; Input voltage: 31 to 60V, maximum current: 30A to 35A
Quiescent current: 15mA (when converting 12V to 20V, a higher output voltage increases the quiescent current)
Output voltage: 12-97V continuously adjustable (cannot be used to lower the voltage)
Output current: 22A (related to the difference between input and output voltage; the greater the voltage difference, the lower the output current. Please improve heat dissipation when the current is above 15A)
Constant current range: 0.8-22A (+/- 0.3A)
Reverse input protection: yes (150A power MOSFET reverse protection)
Input low voltage protection: yes (adjustable from 10V to 50V, self-recovery)
Operating temperature: -40°C to 85°C (If the temperature is too high, please improve heat dissipation)
Frequency: 150KHz
Conversion efficiency: 92% to 97% (Efficiency is related to input/output voltage, current, and voltage difference. The smaller the difference, the higher the efficiency)
Input overcurrent protection: Yes (Automatic protection when the input exceeds 40A and the supply voltage does not increase)
Short circuit protection: Yes (60A input fuse), please be careful to avoid short circuits.
Reverse input protection: Yes (150A power MOSFET, can be connected in reverse for extended periods)
Installation method: Four 3mm standoffs
Wiring method: Terminal blocks (Please (use a thick common copper wire)
Output power: maximum output power = input voltage * 30 A (if input 12 V, maximum output power = 12 V * 30 A = 360 W).(If 24V input, maximum output power = 24V * 30A = 720W)
Weight: 372g / 13.1oz (approx.)
Package List:
1 module
Note:
Please note that the fan for this product will be sent randomly, and please ensure this is acceptable to you before ordering.
Instructions:
The module output should not be short-circuited, and the current should not be measured directly with a multimeter. Short-circuiting will damage the module.
Undervoltage adjustment range: DC10V-50V (clockwise to increase, counterclockwise to decrease). First, set the undervoltage to the minimum, then adjust the input voltage to the required undervoltage protection value. Slowly adjust the value of Turn the dial clockwise to increase the voltage; when the voltage indicator is on, turn it counterclockwise one circle, then turn it back on. Input undervoltage protection is primarily used to prevent the battery from over-discharging when the input power source is the battery. Low battery voltage will damage the power supply module and the battery. When switching the input power supply, the low-voltage protection must also be set.
Adjustable constant voltage range: DC 12–97V (clockwise to increase, counterclockwise to decrease). First, set the voltage to the required voltage, then connect it to the load.
Adjustable constant current range: 0.8–22A (clockwise to increase, counterclockwise to decrease). First, disconnect the load, then adjust the output voltage to the required voltage. Set the current to the minimum (turn the DC potentiometer counterclockwise approximately 30 turns). Connect an ammeter in series with the output, then slowly adjust the current. (The booster module cannot directly adjust the current by short-circuiting.)
The input voltage must not be less than 10V or greater than 60V (when the input voltage is less than 12V, please reduce the load accordingly).
Ensure that the input voltage is at least 2V lower than the output voltage.
If using a switching power supply or other secondary power supply, ensure that its power is 1.3 times or greater than the power rating of the power supply module.
During overcurrent or undervoltage protection, the output voltage will always be close to the input voltage; this protection means there is no overvoltage.