404 Fungicidal Wash is a powerful, fungicidal wash for the removal of lichens, fungi and algae on all mineral surfaces such as walls, paths, roofs, drives etc. It also leaves a residual surface to help prevent further infestation.
Kills mould and fungal growth caused by damp on internal and external floors and walls.
Kills mould and fungal growth on roofs prior to coating with bituminous coatings.
Removes algae, lichen, green slime and fungal growth from patios/drives.
CHARACTERISTICS / ADVANTAGES
Internal and external use.
Leaves a residual surface to prevent future infestation.
Always read label before use and wear suitable protective equipment.
Supplied ready to use. Do not dilute.
Remove all surface debris and growth from the area to be treated. Apply by brush or spray at a rate of 1 litre per 5 - 10m2 depending on porosity of surface.
Leave solution for 20 minutes.
Finally, wash down the area with water. Repeat process for badly infested areas. Take care not to allow residues to run directly into fresh watercourses.
Ready to use - do not dilute
For use only as specified as a surface biocide.EVERBUILD® 405 Path &Patio Seal is a solvent free acrylic coating used to seal and protect patios, paths,
natural stone, concrete and block paving from the effects of sunlight, water, oil, petrol and organic growth.
The milky solution dries to a hard wearing water repellent film which gives a low sheen, slip resistant finish
which will reduce dirt pickup and facilitate easier cleaning.The product is safer to use than conventional solvent based products, i.e. it is non-flammable and
will not harm plants and animals when used as directed.
Where it will protect from the effects of sunlight, water, oil, petrol and organic growth on:
CHARACTERISTICS / ADVANTAGES
Solvent free formulation – non-flammable, low odour.
Improves appearance of paths/stone.
Also acts as a dustproofer and facilitates easier cleaning.
Dramatically improves water and mark resistance -
High degree of water repellency in dried film.
Contains a powerful fungicide – prevents unsightly growth in the film.
M.F.F.T ca 0°C
Drying Time 4 Hours
Consumption 1 Litre will cover approximately 8m² per coat depending on nature of surface
SUBSTRATE QUALITY / PRE-TREATMENT
Surfaces must be free from grease, dust, loose material, algae etc. Clean surfaces with Everbuild Patio Wizard. For bad oil stains, use a proprietary detergent
such as EVERBUILD OIL AWAY and hot water.For very badly soiled surfaces, use Everbuild Brick & Patio Cleaner.In all cases, wash down the cleaned surface with a hose and broom to remove all traces of cleaning product.Pavers must be left for three months minimum after placing before over coating with this product.This will allow salts to leach out which otherwise may cause unsightly white patches appearing beneath the sealer, especially when the patio is wet.
Stir well before use. May be applied to damp (but not wet) surfaces.Apply using a long pile roller and tray or low-pressure spray. Ensure even and thorough coverage, especially on textured finishes where ponding of
the material MUST be avoided. Apply in two coats, allowing no more than 2 hours between coats.An extra coat may be applied if a semi gloss finish is required.
Drying time will be 4 hours from last coat at 20°C. This will be extended at lower temperatures.Do not apply below 5°C.
CLEANING OF TOOLS
Clean tools with warm soapy water before the product dries on them
Areas treated with this product can be cleaned with warm water and detergent or Everbuild Patio Wizard.
Do not use acid based cleaners, as these will remove/discolour the product. Avoid using power
Use only as directed. Store only in original container.
Do not use on surfaces which have been treated with silicone or stearate based water seals (eg Everbuild
Waterseal) unless the surface is weathered enough so as to show no water beading effects.
Do not use if rain is imminent (within 5 hours at 20°C).
Do not apply below 5°C (air or surface temp).
Dispose of this product and packaging correctly.
Do not allow to enter watercourses.
It is the user's responsibility to determine suitability for use.
If in doubt, please contact Technical Services Department for further advice.