REF CEM1_WAT5ME29871690

Everbuild Environmentally Friendly Patio Stain Remover 1L and 402 Water Seal 5L

In stock
In stock
£19.95
£19.95
total
£19.95
Secure Payment
Delivery options
Free delivery (postcode specific) *
Home
  • At home between 24/01/2022 and 25/01/2022 for any order placed before 6 pm - Free delivery (postcode specific) *
Sold by BuyaParcel
 
 
 
 
 
 
 
 
 
 
 
 
Product details
Description
Everbuild Cemstrip is a new type of cement, concrete and mortar stain remover that provides a more environmentally friendly and safer alternative to conventional hydrochloric acid based cement removers. Cemstrip will also remove salts and efflorescence from the surface of mineral substrates and is a very effective general cleaner for removing ingrained dirt, grease and stains from paths and patios. Cemstrip is a highly concentrated formula that can be diluted by up to 10 times with water to suit a variety of applications. Unlike hydrochloric acid based products Cemstrip can be safely used on most metal surfaces such as tools, cement mixers and other building equipment. Cemstrip is Non-hazardous in storage, transport and usage. It is also fully biodegradable.

USES
Removes cement, mortar and concrete on most mineral
surfaces such as paths, patios and walls.
Cleaning tools, cement mixers and other building
equipment.
CHARACTERISTICS / ADVANTAGES
Available in bottles or as a ready-to-use spray.
Water clean-up.
Economical, makes up to 10 times the volume of the
bottle when diluted.

APPLICATION INFORMATION
Yield Approx. 10m2 per litre depending on porosity of substrate.

APPLICATION INSTRUCTIONS MIXING
9 parts water to 1 part EVERBUILD CEMSTRIP
Cleaning general stains and ingrained dirt from paths, patios and horizontal surfaces.
2 parts water to 1 part
EVERBUILD CEMSTRIP Cleaning light mortar stains from paths, patios, walls
or vertical surfaces.
Product Data Sheet
EVERBUILD CEMSTRIP
May 2018, Version 01.01
020405030040000014 1 / 3
1 part water to 1 part EVERBUILD CEMSTRIP Cleaning
heavy mortar stains from walls or vertical surfaces.
Neat Cleaning tools, cement mixers and other building
equipment.
SUBSTRATE PREPARATION
When cleaning paths, patios, cement stains etc. from
surfaces always thoroughly wet surfaces prior to application.
Do not apply to a dry surface.
Always test a small inconspicuous area prior to full application.
When cleaning tools and equipment pre-wetting is not necessary.
APPLICATION
General Cleaning:
Moisten surfaces with water and apply EVERBUILD
CEMSTRIP with brush or low pressure spray (avoiding mist formation) from the top of the area downwards.
Leave for 5-10 mins then scrub/wash off with a hose,
brush or power washer until the surface is clean. Never
allow the product to dry on surfaces. Where a
second application is necessary, repeat the procedure
above.
Cleaning tools/equipment:
EVERBUILD CEMSTRIP will remove fresh cured cement
and wet or semi-cured cement from tools. Spray
onto item in question. Leave for 15 mins to act (light
stains) or up to 3 hours for heavy contamination.
Wash off the product with clean water. Use of a scourer will
assist removal of stubborn stains.
Use a hot power
wash to assist removal of staining from mixing equipment.
After removal, always spray tools with Everbuild
XT44 Maintenance Spray (or any other proprietary
maintenance spray) to prevent further
corrosion/rust.
LIMITATIONS
Do not use on marble, granite or travertine.
Do not use on coloured cement-based pavers.
Always test a small inconspicuous area prior to full application, especially on coloured flags/stones.
Do not use on soft metals such as lead brass, copper
or aluminium.
Do not apply to dry surfaces or allow Cemstrip to
dry on the surface.
Always thoroughly rinse equipment to prevent further
rusting/corrosion.
Avoid overspray on sensitive surface such as brass,
copper, stainless steel and aluminium.
Remove any excess material or spills immediately with clean fresh
water.
Cleaning mortar or concrete from tools the
stronger or older the mix, the more difficult it will be to remove.
Always wash out spray equipment immediately after use with clean fresh water.
It is the user s responsibility to determine suitability for use.
If in doubt contact technical services for advice.Waterseal is a high-performance transparent water repellent specially formulated to prevent water penetration on all mineral substrates such as brick, stone, concrete, pebbledash and rendering.

USES
As an effective water repellent on:
Brick
Stone
Render
Concrete
Pebble dashing

CHARACTERISTICS / ADVANTAGES
Improved durability and beading effect.
Solvent free formula.
Non-flammable.
May be applied by conventional garden spray.
May be applied to damp surfaces.
Active Components Emulsified polysiloxane
(silicone) resin in water

Coverage 5 – 8 m² / litre depending
on porosity and nature of
surfaces being treated.

APPLICATION INSTRUCTIONS
SUBSTRATE QUALITY / PRE-TREATMENT
All surfaces must be clean and sound, free from dirt,
mould, algae, grease and other contamination. Surfaces may be damp not wet. Carry out surface repairs
and fill cracks before application
APPLICATION
Shake well before use. EVERBUILD® 402 WaterSeal
may be applied to dry or damp (not wet) surfaces. Apply by low pressure (garden) spray, brush or roller.
NOTE: THIS PRODUCT WILL DRY CLEAR.
On vertical surfaces, saturate the wall working from
the bottom up, ensuring the entire surface is covered.
On horizontal surfaces, flood the entire area then after
10 minutes, spread out with a soft brush, roller or mop
to ensure the entire area is covered.
Two coats are normally required; the second coat being applied within 1 hour – as soon as the first coat has
soaked in and whilst the surface is still wet. Clean
brushes, rollers and spray equipment with warm water IMMEDIATELY after use.

LIMITATIONS
Do not apply below 10oC.
Do not apply when raining or when rain is imminent.
Do not use on painted surfaces.
Allowing the first coat to dry may prevent penetration of the second coat. Always apply second coat
within 1 hour, or before first coat is dry.

Do not use on wood, plastic or rubber.
Do not use in fishponds.
Do not use detergents to clean the substrate prior to
application of this product - this will dramatically reduce the beading effect.

Note: The surface to be treated may darken after the
first application. Always test a small area first PRIOR to
coating the whole surface.

Do you need more information?

We're here to help!
You are here:
*Free shipping availability will depend on your postcode, this information will be available at checkout.

The biggest marketplace in Europe for DIY, Home & Garden

  • Millions of products

    Loads more than in a shop, and without needing to navigate all the aisles

  • Delivery to your home or click & collect

    Whichever suits you best

  • Hundreds of dedicated experts online

    Like Macgyver but online