HTMC7 DIY Mini Incubator Temperature Control and Automatic Egg Turner Digital Poultry Incubator 220V EU Plug.

1. We provide a complete set of incubation accessories; you only need to prepare a box. 2. When the dual power cord is off, it can be connected to a 12V battery for safe incubation. 3. The exhaust fan ensures uniform heat dissipation, low noise, and a long service life. It features a chipboard and one-touch incubation control. 4. The home incubator's motor has two operating modes: forward and reverse rotation. 5. Heating film and PTC heating maintain a constant temperature, guaranteeing the incubation temperature. 6. Humidity probe with a digital sensor provides stable performance and accurate temperature readings. Specification: Item Type: DIY Mini Incubator. Material: ABS + Aluminum Rated Power: 80W Motor Voltage: 12V Maximum Motor Power: 4W Motor Operating Mode: Forward/Reverse Egg Rotation Frequency: Every 2 hours Temperature Control Range: 37-39℃ Application Area: 48 eggs/56 eggs/96 eggs/112 eggs. How to Use: Temperature and Humidity Setting 1. Test: After connecting each component, turn on the power. You will hear an alarm sound due to the temperature/humidity. Press the button manually to cancel the alarm. 2. Set the Temperature and Humidity, Change the Number of Incubation Days: Press the setting button, press "+" to select the desired temperature, set the humidity and the number of incubation days using the same operation (repeat twice), and finally press "set" to exit the setting mode. (Note: The factory setting is 37.8°C, and you can set it to 37.6°C using the method described above. After setting the number of incubation days, the machine will take effect after restarting.) 3. Setting Low/High Temperature Alarm Settings: Press and hold the setting button for 3 seconds, press +/-, the screen will display AL, then press the setting button again, press +/- to select the low temperature setting. Press and hold the setting button for 3 seconds, the screen will display "AH", and set the high temperature alarm settings in the same way as above. 4. Setting Humidity Alarm Settings: The factory setting for humidity is 45%, no need to adjust it again. (If you need to adjust it, you can do so using the same method as for setting the temperature settings, and the screen will display "AS".) 5. Calibrate the temperature sensor reading: Set the normal temperature reading to 0℃. If it is incorrect, you can adjust it using the same method as above; the screen will display "CA". 6. Set upper/lower temperature limit: If HS (Upper Limit) is set to 38.2 and LS (Lower Limit) is set to 37.4, the original temperature can only be changed from the Package List: 1 panel, 1 motor, 1 exhaust fan, 1 heating film, 1 humidity probe, 1 temperature probe, 1 motor connecting wire, 1 plug, 1 12V power cable, 1 manual, 12 screws, 8 nuts, 8 gaskets, 8 insulation columns. Note: 1. The incubator must be prepared by the user and can be made of wood, acrylic, plastic, or glass. 2. The heating plate temperature can reach 270℃. Please use a gasket to insulate it during connection and installation.3 In the design of the box, it is recommended to make a "sink" in the box to facilitate the addition of water, and the corresponding amount of water can be added according to the required humidity, so that the humidity of each area is within the normal range.4Turning the egg tray over requires another step. Installation Instructions: 1. Find a box to use as an incubator stand. Tips: In the design process, the box size is generally ≥50×50×35cm (boxes are not limited to these two types; here is an example). 2. You need to drill holes in the box to install the accessories. Important Tip: Regarding the screw hole position, please use the actual box as the standard (because the panel needs to be connected to the power supply, for added safety, please add an inner box). 3. The body of the box is carefully perforated for air circulation.