KR2201W‑4 APP Wireless Remote Control 433Mhz Wifi Timing Switch Controller for Light 90‑250V

1、Connect directly to the power circuit, use the app to add devices and connect to your wifi router to achieve networking and remote control without adding a host.

2、The receiver has three working modes: jog mode, self‑locking mode, and interlocking mode, which can meet your different needs.

3、Complete APP functions: Wi‑Fi remote control device status, sharing control, timing, group control and smart scenes.

4、433Mhz frequency, IEEE 802.11 b/gn wifi frequency, high sensitivity, support V1527, PT2262 and HS1527 encoding format.

5、90-250V input voltage, 10A working current, 2200W maximum load power, which has stable performance.

Item Type: Wireless Remote Control

Material: Plastic

Weight: Approx. 56g/2oz

Input Voltage: 90-250V

Working Current: 10A

Maximum Load Power: 2200W

Frequency: 433Mhz

WIFI Frequency: IEEE 802.11 b/gn

Support Encoding Format: EV1527, PT2262, HS1527

Wiring Mode: Null line and live wire 2 in and 2 out

Working Mode: Jog, self-locking, interlocking through the button setting

Size: Approx. 80 x 40 x 25mm/3.1 x 1.6 x 1in

APP: for Smart Life (Domestic available for Tuya Smart)

APP Add Device:

1. Turn on the power of the device after completing the installation.

2. Enter the application, click "+" in the upper right corner of the page to enter the device networks connection page, as shown in the figure below

3. There are two ways of networks connection (normal mode and AP mode). Normal mode is the default mode. Users can click the upper right corner to switch the connection mode to AP mode.

4. Enter the normal networks distribution mode, the indicator light of the device flashes quickly (2 times per second), click Next

5. If the indicator does not flash quickly, press and hold the button of the device for 5 seconds and then release it, or turn the device on and off quickly three times.

If the device is "offline" on the App, it will take a while (within 1 minute) to connect to your router and cloud server due to the networks environment. When the LED is on for a long time, the device is in the "online" state, if the App shows that the device is still in the "offline state", please close the App and reopen it.

For access to third-party smart speaker control, such as for Tmall Genie, for Googel Home, please refer to the instructions in the APP.

Introduction to RF remote control operation (Smart switches with 433MHz/868MHz function support this function, if the device does not support this function, please ignore this introduction)

Clear function: After pressing the learn button of the receiver 8 times, the receiver clears all remote control data stored in the device. When the LED flashes several times, it indicates that the clear function has been completed.

(After clearing the memory codes in the receiver, all remote controls cannot be used with the receiver.)

The working mode of the receiver:

1. Jog mode: Press the button on the remote control to turn on the receiver relay; release the button to turn off the receiver relay.

2. Self-locking mode: Press the remote control button once to turn on the receiver relay; press the button again to turn off the receiver relay.

3. Interlock mode: Press button A on the remote control to turn on the receiver relay, and press button B on the transmitter to turn off the receiver relay.

The working mode setting of the receiver:

1. Set the jog mode

Press the learning button of the receiver once (if the device has a button to switch the relay function, press twice to enter the mode), the LED of the receiver will light up and enter the setting state; press the button of the remote control, the receiver's The LED will flash and then turn off, and the setting is successful.

2. Set the jog mode:

Press the learning button of the receiver twice (if the device has the function of switching the relay through the button, press it 3 times to enter the mode), the LED of the receiver will light up and enter the setting state; press the button of the remote control, the LED of the receiver It will flash and then go out, the setting is successful.

3. Set the interlock mode:

(Note: When selecting "Interlock Mode", you need to set two different buttons on the remote control, the first learning is "ON", the second learning is "OFF". For example: button A = ON, button B = OFF)

Press the learning button of the receiver 3 times (if the device has a button to switch the relay function, press 4 times to enter the mode), the LED of the receiver will light up and enter the setting state; press the A button of the remote control, the receiver's The LED will flash and then stay lit; then press the B button of the remote control, the receiver's LED will flash and then go out, the setting is successful.

Note: The receiver can only store the data of 15 groups of buttons (on the remote control). If the number of saved buttons exceeds 15 groups, the first group of data will be automatically overwritten

APP Function:

1. Wi-Fi remote control device status

Turn on/off by clicking the device icon. The device status is always displayed in real time on the APP.

2. Shared control

The owner can share the device with other "smart life" accounts. When sharing devices, both should stay online in the "smart life". Because if the account you want to share is not online, he/she will not receive the invitation message.

How to realize sharing? First click "Share", enter the "Smart Life" account (phone number or email address) you want to share, check the timer permissions you want to provide (edit/delete/change/enable), and then click "Next" . The other account will receive the invitation message. Click "Accept" and the device has been successfully shared. Other users can access the control device.

3. Timing

Support cycle timing and countdown to turn on/off each device.

4. Group control

Support to organize multiple devices into a group, and simultaneously control a group in the APP

5. Smart scene

Allows to automatically trigger/turn off the device through the scene.

The user selects among the scene conditions, adds different existing equipment, names and saves the scene.

1 x Wireless Remote Control

1 x Manual