Multifunction AC Digital Display on DIN Rail with Current Clamp Measures Voltage, Current, Power, Energy (kWh), Time, Cos φ Wide Range 80-300V AC for Panel

Dimensions and weight

1. Product dimensions: 54 × 80 × 64 mm

2. Packaging dimensions: 85×60×70mm

3. Unit gross weight: 0.134kg. This multifunction digital meter with a guide rail display simultaneously shows AC voltage, AC current, power factor, active power, electrical energy, and consumption time. Main technical specifications:

1. Measurement accuracy: 1% ± 2 digits

2. Display: Voltage is displayed on a 0.31-inch red LED digital tube with 4 digits; current and time are displayed on 5 digits. A 0.31-inch red LED digital tube displays active power and energy (kilowatt-hours) on 5 digits; a 0.31-inch green LED digital tube displays energy (kilowatt-hours).

3. Measurement Range: AC Voltage: 80.0-300.0 V (or 200.0-450.0 V, to be specified by the user when ordering); AC Current: 0-100.0 A. When the measured current is less than 100 A, the display resolution is 0.01 A; When it is greater than 100µA, the display resolution is 0.1µA. The range change is automatic. Power consumption: (Measurement voltage: 80.0-300.0V AC) 0.0-30,000W (200.0-450.0V AC: 45,000W)

Energy consumption: 0.000-99,999kWh, automatic decimal conversion

Energy accumulation: 0.00-999.59h

Power factor: 1.000-0.000
4. Measurement frequency: 2 measurements per second
5. Weight: 145g per unit
5. Dimensions: 54(L)×80(W/H)×64(D)mm

7. Installation width: The instrument occupies the location of the 3P pneumatic switch (DZ47/C45)

8. Dimensions of the instrument's protruding parts: 54 (length) × 45 (width/height) × 16 (thickness/depth) mm

9. Installation method: On rail (standard guide rail). Note: Guide rail not included.

10. Integrated current transformer: The measuring wire passes through the round opening on the right side of the device (diameter: 11 mm, compatible with standard 12 mm² pin cables/maximum current of 100 A). Note: The load can be inserted through the annular opening of the device, from the top or the bottom, without affecting measurement accuracy.

Extreme Operating Environment
Operating Temperature: -10°C to +60°C
Operating Humidity: 10% to 80% (non-condensing)
Operating Atmospheric Pressure: 80 kPa to 106 kPa
Avoid direct sunlight.

Operating and Wiring Instructions (Read Carefully)

1. Connect the voltage to be measured to terminals 1 and 2 located at the bottom left of the device.

2. Wiring diagram of the integrated current transformer: Insert the measuring wire into the opening located under the device. The direction of insertion is irrelevant; the wire can enter through the lower opening and exit through the upper opening, or vice versa. The direction of insertion does not affect the measurement results.3. After powering on, the device displays the voltage (M), current (A), and active power (W). The red LED to the right of the corresponding display window illuminates, indicating the displayed function. 4. Press the (SAMCK) button on the right side of the control panel. The three display functions then change to show the power factor (cos), accumulation time (h), and energy (owh). The green LED to the right of the corresponding display window illuminates, indicating the displayed function. 5. Press the (SAMCK) button again. The device again displays the voltage (V), current (A), and active power (M). 6. To reset the energy measurement and timer (start the measurement from zero), select the energy measurement mode. The green LED to the right of the display illuminates. Next, press and hold the (SAMCK) button for 5 seconds (or 5 minutes) until the energy and timing displays show 0. Release the button. The energy and timing displays will then restart the measurement from zero. In the event of a power outage, the energy and timing displays are equipped with an automatic data saving function. Thus, in the event of a power outage or disconnection, the device automatically saves the current test data. As soon as power is restored, the device resumes the measurement and accumulates zeros over the previously recorded data. This product is sold on behalf of a third party.