Set of 2 transparent TPE car shock absorbers, spring buffers, type B-

Key Features: 1. Significantly improves driving stability, adds driving comfort, and enhances the driving experience. 2. Effectively reduces body vibration and absorbs suspension system noise. 3. Addresses weak springs and raises the car body by 0.2 to 0.3 cm. 4. Improves safety while driving and cornering, protects the frame, and increases load-bearing capacity. 5. Dampens and absorbs the sudden pressure caused by rough road surfaces, preventing damage to the suspension system. Specification: Features: Significantly improves driving stability, adds driving comfort, and enhances the driving experience. Effectively reduces body vibration and absorbs suspension system noise. Addresses weak springs and raises the car body by 0.2 to 0.3 cm. Improve safety protection while driving and cornering, protect the chassis, and increase load capacity. Dampen and absorb the instantaneous pressure caused by uneven road surfaces to prevent damage to the damping system. Extend the life of the shock absorber and improve braking efficiency. Specifications: Material: TPE Color: Transparent Optional Type: A-, A, B-, B, C, D, E, F Package Weight: Approx. 1658g (A-), 1300g (A), 719g (B-), 806g (B), 711g (C), 383g (D), 321g (E), 386g (F) Function Overview: 1. Fully improves driving stability, enhances driving comfort, and enhances the driving experience; 2. It can reduce body vibration to a certain extent and absorb suspension system noise; 3. Address the issue of spring weakness and increase the spring body length by 0.2 to 0.3 cm; 4. The limited buffer absorbs the instantaneous pressure caused by bumpy roads to prevent damage to the shock absorption system. Installation Method: 1. It can be installed in a 4S workshop. Before installation, park the car on a level surface and prepare a pad of adhesive, a jack (if it is more convenient to mount a roof rack), and soapy water (or diluted water with detergent); 2. Use a jack to lift the car body from the installation location (or the upper chassis to lift the entire vehicle). The spring will be extended to facilitate installation. The suspension spring will be fully visible, so there is no need to lift it excessively. 3. Spray soapy water to clean the spring (mainly to remove sand stains from the spring surface), and also spray a little soapy water to lubricate the rubber of the buffer (sufficient lubrication will make the spring easier to position and adjust). Thoroughly clean the spring with soapy water after installation to prevent the damping springs of automotive safety parts from rusting and breaking, which could cause injury. 4. Install the rubber buffer in the center of the spring. Lower the car body after installing the wheels and check that the spring is inserted into the upper and lower grooves of the rubber buffer. Installation Skills and Experience: 1. The specifications of the rubber buffer are primarily directly related to the spring spacing. Please note that the specifications of the installed rubber buffer must be matched to the corresponding spring. If the specifications do not match, do not install it. 2.Regardless of the overall spring design (straight, conical, inverted, barrel-shaped), the shock absorber rubber must be installed in the center of the spring to achieve the desired effect. Whether the rubber opening of the cushion faces outward or inward does not affect its performance, but an inward opening will look better. 3. When the car body is raised, the spring is under tension, and the gap between the spring and the rubber during this tension may not align with the cushion's dimensions (therefore, the car body should not be raised too high). Try to insert the spring into the gap in the rubber cushion or insert it into the slot on one side. When slowly lowering the car body, check that the spring is fully seated in both the upper and lower grooves of the shock absorber rubber. 4. After correctly applying the cushion adhesive, it is recommended to use nylon cable ties to secure the cushion adhesive and the spring assembly to the adhesive hole in the cushion. When lifting the top, it is not easy for the spring to come out of the adhesive slot in the pad. Things to pay attention to after installation: 1. After the