STC-200 20L 70W electronic water-cooled digital heating and cooling machine

Features:

1. Adopts semiconductor refrigeration, environmentally friendly and pollution-free, greatly beneficial.
2. Silent operation, low power consumption design, ideal for use in an aquarium; supports both cooling and heating.
3. Utilizes a digital display and advanced intelligent microcomputer temperature control technology.
4. Comes with Celsius and Fahrenheit temperature switching functions, very convenient.
5. The product is suitable for small-scale refrigeration and heating, aquaculture, and aquariums.

Specifications:

Item Type: Electronic Water Chiller
Material: ABS + Metal
Purpose: Plumbing Equipment
Model: STC-200
Model STC-200 20L
Rated Voltage: DC12V
Power: 70W
Circulating Water Pump Flow Rate: 1-3L/min
Suitable Range: Water pump with a vertical lift height of three meters below the surface
Cooling Water Capacity: ≤20L
Suitable Water Pipe: Inner Diameter 8mm
Product Size (approx.): 115 x 110 x 190 mm / 4.5 x 4.3 x 7.5 inches
Net weight 1.80 kg / 4 lb (approx.)
The kit includes two meters of water pipe, two hose loops, a water pump, a power adapter, and instructions for connecting the water pipe to an electrical line:
The 2 meters are divided into two sections (the length can be determined according to your needs). Place the hose loops onto the pipe, connecting the inlet and outlet pipes. Secure the loop firmly to the pump, and the power supply can be used directly.
1. Turn on the power; the water should start flowing. Check for leaks.
Installation and Use:
A. Install the connection as shown in the figure.
B. The machine and the surrounding area must maintain a distance of more than 20 cm to facilitate heat flow. C. Transport, installation, and maintenance: please handle with care. Temperature control setting method: The "SET" light is on when the water cooler is in the set state; the "Work" light is on when the water cooler enters operating mode. "SET" setting button, "ENTER" confirmation button, "+" heating button, "-" cooling button. Briefly press the "SET" button (to set the temperature), then press the "+" or "-" button until the desired temperature is reached. (Set after pressing "ENTER" or 10 seconds after automatic return to the current temperature)
Detailed Function Table:
1. In normal display mode, press and hold the "S" button to display P0. Press the "S" button again to select P0-P5 (each press of the "S" button displays the cycle increments from P0 to P5). Press the "E" button to confirm, then press the "▲" or "▼" button to set the thermostat function.
2. As shown in Table Two. (After setting, press and hold the "S" button for 10 seconds to automatically return to the current temperature.))
Symbol Meaning Degrees Celsius Degrees Fahrenheit Default Value
P0 Refrigeration, heating, cooling mode C/H/ CH C/H/CH C
P1 Return temperature 0.1~15 0.1~27 2
P2 Correction temperature -7~7 -13~13 0
P3 Time delay (min) 0-10 0-10 3
P4 High temperature alarm temperature -50~110 -58~230 110
P5 Temperature pattern (degrees Celsius and Fahrenheit) CCCC/FFFF CCCC/FFFF CCCC Sensor fault display E1, close all outputs
1. This product is shown with a cooling water temperature of 28°C, without high-power lights or submersible water pumps, assuming the water temperature can be reduced to approximately 25°C. The higher the water temperature before cooling, the less cooling water is required. The amount of hot water used in the cold and hot water production process is equal to the cooling capacity of the refrigeration system.
2. The upper temperature limit of this product is 40°C, the lower temperature limit is 0°C.
Danger:
Warning:
Caution:
Operation not in accordance with specifications may be dangerous.
If there is a power line or other fault, please contact professionals.
Illegal operation may damage the product.
Cleaning and Maintenance:

Package List:

1 x Electronic Water Cooler

1 x Power Adapter (10A)

1 x Water Pump

1 x Power Cord Plug

< p>1 x hose

2 x hose loops

1 x user manual (2 pages)

Note:

1. Do not use outside the voltage and current range. 2. When in operation, the operating indicator is red.