Microcomputer Thermostat, DC 12V Digital Thermostat, All-Purpose Digital Temperature Controller with Sensor, Temperature Controller

1. This delicate digital display temperature controller can set Celsius mode or Fahrenheit 2 mode. The display and control temperature can be set to 0.1℃. It is convenient to install and the wiring is simple 3. Wide temperature measuring range from -50℃ to 110℃ and supports high temperature protection 4. Can be installed directly or integrated into industrial control equipment panel, convenient and quick 5. Widely used in hatching area, equipment case, air conditioning system, temperature control protection and other fields Specification: Features: This delicate digital display temperature controller can set Celsius mode or Fahrenheit mode. The accuracy of ambient and set temperature is 0.1℃. It is convenient to install and the wiring is simple.Wide temperature measuring range from -50℃ to 110℃ and supports high temperature protection. Can be installed directly or integrated into industrial control equipment panel, convenient and quick. Widely used in hatching area, equipment case, air conditioning system, temperature control protection and other fields.Specification: Input voltage: DC12V Temperature measuring range: -50℃~110℃ Resolution ratio: -9.9℃-99.9℃--0.1℃ other temperature intervals--1℃ Measuring accuracy: 0.1℃ Control accuracy: 0.1℃ Feedback difference accuracy: 0.1℃ Rate refresh rate: 0.5s High temperature protection: 0-110 ℃ Measuring input: NTC waterproof sensor (10K0.5%) Output: 20A relay Environmental requirements: Temperature requirement: -10 ℃~60 ℃ Humidity requirement: 20% to 85% Machine power consumption: static current ≤ 35 mA, starting current ≤ 65mA. Digital tube: LLL sign is sensor open circuit and HHH sign means beyond the measuring range, the controller will forcibly disconnect the relay, --- sign means high temperature protection.Function Parameter Description: Please press SET button five seconds, then it can enter the main setting menu, pressing STC(+) and C/F(-) can switch to P0-P8. About P0-P8 parameter setting, when you need to adjust P0, please first press STC(+) and C/F(-) at the same time, and the P0 figure will flash, secondly, press STC(+) and C/F(-) to adjust, if done, finally press STC(+) and C/F(-) to confirm at the same time, P1-P8 which can be set the parameters of each code as P0 according to the needs which are specific to them. C/F key is a key to change Fahrenheit orCelsius Press C/F key once, and it will manifest F(Fahrenheit mode), then press C/F key once, it will display C(Celsius mode), the default mode is C(Celsius mode), if there is a big temperature error when you use it, maybe it is F mode.An example setting: If you need to control the refrigeration equipment 1: Please switch to C mode in P0 code: 2: In case of actual temperature manifestation, you need to press SET key, and the following digital setting text will flash, then press C/F (+) and SET (-) to set the cooling stop temperature, after setting, please wait 3 seconds, it will automatically confirm return.3:Back difference setting: Firstly, please press SET key for five seconds all the time, and it will enter the main setting menu, secondly press STC(+) and C/F(-) to switch to P1, when switching to P1, please press STC(+) and C/f(-) once at a time, the P0 figure will flash, then press STC(+) and C/f(-) to set the difference value (the return difference means you need to add several degrees to start, for example, if it stops when the stop setting temperature is 25 degrees, you need to set the cooling temperature to 28 degrees, the value in P1 code should be set to 3 degrees, so the return difference value is 3 degrees), after finishing that, finally press STC (+) C/F (-) at the same time to confirm.4: The above steps are configured, the data is automatically recorded, and the final result is, in the control of refrigeration equipment, above 28 degrees to start refrigeration, refrigeration to 25 degrees to stop. If you need to control the heating equipment: 1: Please set to H mode in P0 code. 2: In the case of actual temperature manifestation, you need to press SET key, and the following digital text will flash, then press C/F (+) and SET (-) to set the heating stop temperature, after setting, please wait 3 seconds. , it will automatically confirm the return.3: Return difference setting: Firstly, please press SET key for five seconds all the time, and it will enter the main setting menu, secondly press STC(+) and C/F(-) to switch to P1, when switching to P1, press STC(+) and C/f(-) once at a time, P1 digit flashes, then press STC(+) and C/f(-) to set the value of difference (the return difference means you need to add several degrees to start, for example, if it stops when the stop setting temperature is 25 degrees, you need to set the heating temperature to 22 degrees, the value in codeP1 should be set to 3 degrees, so the return difference value is 3 degrees), after finishing this, finally please press STC (+) C/F (-) at the same time to confirm.4: When the above steps are all configured, the data is automatically saved, so that the heating equipment control starts the heating system below 22 degrees and stops heating when the temperature is 25 degrees. Code Explain Setting range Factory setting P0 Heating/cooling H/C C P1 Feedback difference 0.1-30 2.0 P2 Maximum limit set +110 110 P3 Set limits at minimum -50 -50 P4 Temperature correction -15-15 0 P5 Delay start 0-10 0 P6 High temperature alarm -50 ~ 110 OFF P7 CS/FH cs F8 Factory Reset ON-OFF OFF Note: Please note that the new type and old type of this product will be sent randomly, and make sure you do not mind before ordering.