Switch of thermostat durable of correction of temperature bicolore, for cabinets

Features:

1. This controller of temperature is designed with a display LED bicolore and has a high precision of 0,1 ℃

2. It takes in load the correction of temperature, the alarm of temperature and the function of start differ

3. Designed with terminals to screw for a wiring practical and easy

4. The probe water-resistant has udoes sensitivity more high, sealed with the silicone, more suitable to the detection of the temperature of liquid, safe and durable

5. Widely used for the control of the temperature in the cabinets, the equipment industrial, the tighten of vegetables and of flowers, etc.

Specifications:

Features :

This controller of temperature is designed with a display LED bicolore and has a high precision of 0,1 ℃.

It takes in load the correction of the temperature, the alarm of temperature and the function of start differ.

Designed with terminals to screw for a operation practical and easy. wiring.

The probe water-resistant has udoes sensitivity more high, sealed with the silicone, more suitable to the detection of the temperature of liquid, safe and durable.

Widely used for the control of the temperature in the cabinets, the equipment industrial, the tighten of vegetables and of flowers, etc.

br>Specifications :

Range of control -50 ℃ ~ 110 ℃

Precision of control 0,1 ℃

Input of the sensor Sensor water-resistant NTC10K L=0. 5M

Alarm of temperature -49℃~110℃

Voltage of input DC12V

Type of output Output relay max. 10Has

Difference of return adjusted 0,1 ~ 30 ℃

Start differ 0 ~ 10 minutes

Correction of the temperature -10 ℃~+10 ℃

Display red Temperature measured

Display vertReglage of the temperature

Instruction :

Terminal K0 K1 :

The type of output of thermostat is a output relay, K0 and K1 are equivalent to a switch of relay d'extension ; the power supply 12 V power supply thermostat, the sensor detects the temperature, the output of the relay of control of the programme of control of the temperature internal and the load (if the load is powered by a power supply CA, it is more safe of connect K0 and K1 at the wire powered on)

Range of adjustment of the function of the code Mode of control of temperature by fault P0 H (hot)/C (cold) C

Adjustment of the difference of return P1 0,1 ~ 30 ℃ 2 ℃

Correction of the temperature P2 -10 ~ 10 ℃ 0 ℃

Start differ P3 0 ~ 10 (min.) 0

Alarm of temperature P4 -49 ~ 110 ℃ 110 ℃ Button « SET » : adjust the switch

Button « + » : increase the temperature

Button « - » : reduce the temperature

Restore the settings of machined : On, press and now pressed in the button "+" and "-" set during approx. 3 seconds.

Mode of control of the temperature P0 :

This parameter must be set for the first times to the helps of the controller. it is used for the heating, adjust-the on H ; it is used for the cooling, adjust-the on C.

Difference of return P1 :

Press and now the button SET for access at the adjustment internal, select the adjustment P1, press to new on the button SET for set the value of difference of return. (The value of difference of return is the value that the controller redemarre after have reaches the temperature adjusted and is stop. For example, if we utilisons the mode heating, faisons in output that the controller stops to 40 ℃ and redemarre to 35 ℃, the value of difference of return is of 5)

P2 Correction of the temperature :

This function is used for the correction of the temperature, it exists a gap between the temperature measured and the temperature actual. Temperature of correction = temperature measured + value of correction.

For example, if the temperature measured is of 25,6 degrees and the temperature actual is of 25,8 degrees, set P4 on 0,2, therefore the temperature finale is of 25,6 + 0,2 = 25,8 degrees

Start differ P3 :

This function is normally used for the refrigeration by compressor. If the controller is used in of refrigerators-congelateurs, this value must be defined. According to the against-pressure of the compressor, this value can be adjusted between 3 and 6 minutes. If you the users not for control the compressor or if you n'avez No need to function of retard, you can l'ignorer.

Alarm of temperature P4 :

Adjust the value of alarm of temperature, when the temperature in time actual exceeds this value, the display turn signal for triggering alarm.

Exemple of adjustment of the mode of heating :

Check the equipment of heating electric for stop the heating to 35 ℃ and redemarrez when the temperature descend to 30 ℃ ;

1, press and now the button SET during 3 seconds. for enter in the adjustment internal, set P0 on H.

2, press and now the button SET for revenir to the display of the temperature in time actual, press to new on the button SET and the screen green turn signal, then fit the value to 35 ℃.

3, the difference of return by fault is of 2, it must be defined on 5 if you desired redemarrer to 30 ℃. Press and now pressed in the button SET for access at the adjustment internal, select P1, modifications the value P1 to 5.

Exemple of adjustment of the mode of cooling :

Check the refrigeration of the air conditioning for stop the cooling to 23 ℃ and redemarrez when the temperature reaches 27. ℃ ;

1, press and now the button SET during 3 seconds for enter in the adjustment internal, set P0 on C.

2, press and now the button SET for revenir to the display of the temperature in time actual, press to new on the button SET and the screen green turn signal, then fit the value to 23 ℃.

3, the difference of return by fault is of 2, it must be defined on 4 if you desired redemarrer to 27 ℃.

Press and now the button SET for enter adjustment internal, select P1, changes the value P1 to 4.

Package Includes :

1 x controller of temperature