WS55-220 DC 48V 500W CNC Brushless Spindle BLDC Motor Driver Controller

Features:

1. The WS55-220 is a high-performance and economical three-phase BLDC motor controller. The voltage range is 20VDC to 50VDC.
2. The controller can drive BLDC motors with or without Hall effect sensors.
3. The driver is based on advanced technology and features high speed, high torque, low noise, low vibration, overcurrent protection, overload protection, reduced phase line protection, phase line short-circuit protection, alarm output, and speed signal output.
4. This controller can be used in small equipment, power tools, exhaust fans, jade grinders, vibrating motors, etc.
5. External potentiometer control/external voltage control

Specifications:

Features:
The WS55-220 is a cost-effective, high-performance, three-phase BLDC motor controller. The voltage range is 20V DC to 50V DC.
The controller can drive BLDC motors with or without Hall effect sensors.
The driver is based on advanced technology and features high speed, high torque, low noise, low vibration, overcurrent protection, overload protection, and fewer phase lines. Protection, phase line short-circuit protection, alarm output, speed signal output, positive and negative rotation control, etc.
This controller can be used in small equipment, power tools, exhaust fans, jade grinders, vibrating motors, etc.
External potentiometer control/external voltage control.
With overvoltage protection, overcurrent protection, and rotor lock protection.
Specifications:
Rated Voltage: 20 to 50 VDC
Rated Current: 12 A
Current Limiting: 15 A
Maximum Speed: 20,000 rpm (specific speed depends on the motor itself and the load)
Storage Temperature: -20°C to +65°C
Operating Environment: Avoid direct contact with dust, fumes, and corrosive gases
Temperature: 0-45°C
Humidity: < 80%, frost-free, frost-free
Shock: 5.9 m/s² maximum
Storage humidity: 0 ~ 95% RH
Size: approx. 9.5 x 6 x 3.5 cm / 3.74 x 2.36 x 1.38 inches
Weight: 258 g
Details:
1. Two speed control modes:
External potentiometer: speed control via this potentiometer;
External voltage: speed control via 10VDC external voltage;
Note: two speed control modes cannot be used simultaneously.
2. PG Speed ​​Output Signal: There is a 5V pulse output between the port and ground.
The output frequency is set to P (Hz), the logarithm of the motor class is N, and the speed is F (RPM), so the output speed frequency is P=F*N/60.
3. ALM Alarm Output Signal: There is a 5V alarm pulse output between the port and ground.
4. Positive Reversing Function:
F/R: By flipping the toggle switch on the corresponding side, the motor direction can be reversed. For the toggle switch, the white part is up; flip it up. For the toggle switch, the white part is horizontal and the twang is horizontal.
5. Start-stop (two control modes):
1. External switch FR:
Transfer via the switch.
2.Side rocker switch EN: For the rocker switch, the white part is up and down, then down again to start; for the rocker switch, the white part is horizontal, then press to start.
Note: You can only turn one control at a time; one switch is closed and the other is active.
6. Locked rotor protection: If the motor stops running, re-energize to restart.
7. Power indicator: Green light: Power on and off.
8. Status indicator: Red light: Two flashes in standby mode; after starting, off.
9. Insulation resistance: >100 Ω at room temperature and atmospheric pressure.
10. Insulation resistance: at normal temperature and pressure, 0.5 kV, 1 minute
Package included:
1 x Motor driver controller with cable
Note:
Please note that the new and old types of this product will be sent randomly, and make sure you don't mind this before ordering.