XH - 3002 Microcomputer Digital Temperature Hatching Controller

Features:

1. A variety of perfect use areas, convenient operation and convenient adjustments, is your side temperature control housekeeper.
2. It is precise and reliable with good long-term stability. Convenient to install and repair. Small size, low power consumption, fast response.
3. Easy operation, to set start temperature, stop temperature, corrected temperature connector, etc.
4. Suitable for hatching, breeding, air and water temperature control and other related temperature detection and control.
5. Specifications are optional, precise temperature control, temperature calibration.

Specifications:

Item type: digital temperature controller
Material: plastic
Weight: approx.51g / 1.8oz
Operating voltage specifications: 12V, 24V, 110-220V
Accuracy level: 0.1
Temperature measurement range: -50-110 (℃)
Temperature measurement accuracy: -15-65 (℃)
Temperature measurement accuracy: Humidity: 1 (RH)
Temperature measurement error: ±1 (℃)
Applicable environment: -15-55 ℃ / 20%-85%RH
Product built-in hole Size: 73mm / 2.9in, hole diameter (φ4mm)
How to use:
1. Press the setting button once to enter the internal menu, the default display is P0, press the setting button again and set the required start temperature using the up and down buttons.
2. Press the setting key once to enter the internal menu, the display is P0, switch to P1 via the up and down keys, press the setting key again and set the required shutdown temperature via the up and down keys.
3.Enter the internal menu in the same way, switch to P2 via the up and down buttons, press the setting button again and set the required calibration temperature via the up and down buttons. (Note: In setting, if the detected temperature value is 0.5°C higher than the actual temperature value, then the calibration temperature that needs to be set is -0.5°C. If the detected value is 1°C lower than the actual value. Temperature value, the calibration temperature that needs to be set is 1°C. Detection temperature + Correction temperature = Actual temperature.)
4. Enter the internal menu in the same way, switch to P3 by pressing the up and down buttons, press the setting button again and set the required delay time via the up and down buttons in minutes. (Note: Delay start is generally used for compressor refrigeration.If used for refrigerators and freezers, this value must be set. Depending on the compressor back pressure, the general setting value is 3-6 minutes. If you are not used for control or no delay function is needed, just skip it.
Temperature control mode
1. Essential adjustment parameters:
Start temperature 2. Setting method: Press the setting key to enter the internal menu, set the boot. temperature via the value P0 and set the stop temperature via the value P1
Use case: Control the water heater, stop heating at 50°C and start heating again when the temperature returns to 40°C, how to adjust it?
1. Make sure the operating mode is heating mode, start temperature 2.Press the setting key to enter the internal menu, select P0 to start the temperature and set the P0 value to 40°C.
3 . Press the Set key to enter the internal menu, select P1 to stop the temperature and set the value of P1 to 50℃
Cooling mode
1. Essential setting items: start temperature > stop temperature (the program automatically judges the working mode to be cooling mode)
2. Setting method: Press the setting key to enter the internal menu, set the start temperature through P0, and set the stop temperature through P1 value.
Use case: Empty cabinet radiator, heat dissipation stops at 26℃ and temperature rises. to 30℃ to restart the heater, how to adjust it?
1.Make sure the working mode is cooling mode, start temperature > stop temperature.
2. Press the setting key to enter the internal menu, select P0 to start temperature change, and set the P0 value to 30°C.
3. Press the SET key to enter the internal menu, select P1 to stop the temperature, and set the value of P1 to 26℃.

Package List:

1 x Temperature Controller

Note:

1. Press and hold the up and down keys at the same time, wait until the screen displays 888 to restore factory settings.2. The screen displays LLL, indicating the temperature probe is not plugged, disconnected or damaged, simply replace it.3.The HHH screen indicates that the temperature probe is shorted and exceeds the temperature detection range.

-Contact our customer service in case you need further assistance